Use of Locktite can prevent set screw from twisting loose over time. Align the upper hinges and screw the set screw into the hinge plate on the header. Set the hinge on the bottom of the bookcase onto the pin of the hinge plate on the threshold. Thread the included setscrew/capscrew into the threaded.įor an outswing door, you will work from the backside of the Invisidoor to put it into place on the lower hinge pin and install the capscrew through the top. Mount hinge plate #2 to the top of the bookcase. Then drill a 5/8” hole from the inside of the bookcase through the top to avoid tear out inside the bookcase.) (Predrill a small hole from the top of the bookcase. Use the diagrams for the location of this hole. Prior to installing the upper hinge on an outswing door to the bookcase, an access hole for the set screw must be drilled through the top of the bookcase. Use the mounting diagram to install hinge plate #1 to the bottom of the bookcase. Use blocks of a different thickness to create appropriate height and margin for your application. Install the mounting blocks (usually two 11/16” blocks on the bottom and one 1/2” on the top) to the hinged side of the bookcase unit. Shim the jamb as needed at location of pivot hinge for a solid mounting area with longer hinge plate screws mounted into header for final installation. Install a hinge plate #4 to the upper jamb. Place the two steel washers and bronze bearing onto the hinge pin as shown. Use the diagrams to install hinge plate #3 to threshold/floor. Walls more than a standard 2” x 4” thick may require modification for an inswing door application. Trim will later be mounted over the drywall and bookcase face frame, spanning across the jamb. In most cases, the bookcase face frame will be flush with the drywall. ![]() Use the diagrams to identify locations for the pivot hinge to be installed on the left or right side of the unit as either an outswing (which pulls out toward the bookcase side) or an inswing (which rotates away from the bookcase side). Left and right edge of the face frame rounded over with 3/8” radius bit.The thickness of the blocks may need to be adjusted based on the clearance and spacing needed for the door. Screw 2 mounting blocks into this pocket.Sides and back run down past the bottom shelf, but not as far as the face frame (forms a pocket on the bottom of the bookcase.). ![]() Bottom shelf is flush to the face frame (inside the bookcase).½” plywood glued and nailed to the back for strength to prevent sagging.Face frame (2-1/4” wide) glued and nailed to carcass.Top, bottom, and fixed shelf are dadoed into sides for strength to prevent sagging.Modify design as appropriate for custom applications: ![]() In all cases, it is recommended that you create a template to mock up the dimensions of the opening and the bookcase to verify that you have the necessary clearance for your door to operate properly.ĭesign recommendations based on our universal bookcase. Modifications to the width or depth of the bookcase will likely require changing the spacing allowed for clearance or location of the hinge pivot point. This will eliminate the chance of damaging the finished product during the process of mounting the hinges and adjusting the unit.ĭimensions given with these instructions are based on the size of the universal InvisiDoor (for standard 36” x 80” finished openings) to assist you in sizing your bookcase and finding the appropriate hinge locations. ![]() It is recommended that you test mount the hardware and install the Invisidoor prior to applying stain and finishing coat. Verify that the floor of the opening has adequate support for weight of the unit and holding power for the screws. The Invisidoor pivot hinge is designed to be installed with the bottom hinge plate secured to stable, solid wood. Correct operation and appearance of the Invisidoor requires that the opening be level and plumb or you need to make accommodations for it. Check out the video to learn about the benefits of the InvisiDoor, and read on to find out just how easy it is to set up and install!Ĭheck the opening into which the Invisidoor will be installed to verify that it is plumb and level. Our hidden door solutions come ready to install, and installation is easy enough for anyone to handle, only requiring as little as a drill. The InvisiDoor by Custom Service Hardware is one of our most popular products, and it’s no secret why.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |